LXC7220 generator controller replacement of DSE7120 / DSE7220 /
DSE7320, temperature,25 ~ + 70 degree
Control function automatically switches mains power monitoring and
mains/power generation added to the LXC7210 based
on(AMF),especially suitable for stand-alone automated systems.Its
main features are as follows:
*32-bit ARM mircrocontroller,hardware integration and high
reliablity have been further enhanced.
*The oversized LCD LCD240*128,with backlight,Chinese,English and
other languages optional interface operation.All parameters can be
set on the controller,convenient debugging personnel test machine.
*Of Things Internet through GPRS mobile network and the Internet,in
any network can
*Particularly for the management of the leasing industry provide
the perfect solution:remote management via PC leased units Monitor
all operating parameters(oil pressure,water
temperature,voltage,current,power,etc.)can change the configuration
at any time to protect inappropriate application of the
unit,recorded 200 detailed fault information,including:time to
failure,because,when the key parameters of
voltage,current,power,oil pressure,water temperature,etc,and
etc.,and at any time can be uploaded to the monitoring
machine.Another multi-level password management items to facilitate
the lease management.
*RS485 communication interface, using the MODBUS protocol can
achieve "three remote" function.
*Control and protection functions: diesel or natural gas generator
sets, automatic start / stop, sub-gate (ATS switch)Perfect failure
*Parameter setting: Allow user to change the setting of its
parameters, PC can be directly connected via USB
controllerSettings. Memory in the internal FLASH memory when the
system is powered down, it will not be lost.
Note: All parameters can be adjusted from the front panel of the
*SMS function, the alarm signal when the generator set alarm can be
automatically sent to the set of five phone numbers Interest via
SMS to control the generator set and generator set access state;
using a PC via RS232 ,RS485 interface adjustments queries via the
Internet using a PC (need to connect the DTU).
*A variety of temperature, pressure, oil level sensor curves can be
used directly, and can be custom sensor curve.
*A variety of starting conditions (speed sensors, hydraulic, power
generation) to select.
*Fault history, real-time clock, timer switch (monthly / weekly /
daily boot time and can be set whether
With load) functionality.
*All output ports are relay outputs
|Working voltage||8.0-35Vdc continuous|
|Alternator votage input:Three-phrase four wire||20V AC-360VA(ph-N)3 Phase 4 wire|
|Three-phrase three wire||30V AC-620V AC(ph-ph)3 Phase 3 wire|
|Single-phrase two wire||20V AC-360V AC(ph-N)|
|Two-phrase three wire||20V AC-360V AC(ph-N)|
|Overall Power Consumption||<3W(Standby mode:<=2W)|
|AC generator frequence||50/60HZ|
|Speed Sensor voltage Vpp||1.0-70V(Peak to Peak)|
|Speed Sensor frequence||10,000 Hz (max)|
|Starting relay output||The 16Amp controller power supply voltage output|
|Fuel relay output||The 16Amp controller power supply voltage output|
|Programmable relay outputs 1||7Amp 250VAC passive output|
|Programmable relay outputs 2||7Amp 250VAC passive output|
|Programmable relay outputs 3||16Amp 250VAC passive output|
|Programmable relay outputs 4||16Amp 250VAC passive output|
|Programmable relay outputs 5||The 7Amp controller power supply voltage output(LXC7220)|
|Programmable relay outputs 6||The 7Amp controller power supply voltage output(LXC7220)|
|The size of holes||186mm*141mm|
|Current transformer secondary current||Specified 5A|
IP55:when the installation of waterpoof rubber ring between the
controller and the
IP42:when the installation of waterpoof rubber ring between the
controller and the
control panel does not.
|Dielectric Strength||Object:Between the input/output/power|
|Test Methods:AC1.5kV/1min Leakage current:3mA|
Edited by Lisa Sun